Most of the parts are made by demand so be aware of a certain time of delivery

		Prices
	Improved damper rods - prepared for cartridge emulators (set of 2) Price without emulators - (last time I checked they were 110 €) More info on my YouTube-Channel NB! When ordering please state this measurement Also inform me if the damper rod is with one or two seals. Seals and springs are reused from the original damper so these are not a part of the kit	125 €
	Master cylinder rebuild with piston in desired diameter (incl. seals and spring)	115 €
	New and improved swingarm axle for needle bearings or POM bushings (not included) Unlike other axles, this is surface hardened and has full diameter the complete length, which makes it stiffer. The large thread is made in stainless steel and the nuts too, so no problems concerning rust. The axle is made especially for the modification mentioned below, but can still with advantage be used without.	135 €
	Frame bushings for stiffening the swingarm mount (including new swingarm axle without bearings/bushings) "From"-price is if get frame and swingarm dismanteled (and cleaned) "Commercial video" about the problem - and the service I offer	from 265 €
NB: Particular long time of delivery Price is estimated. Depends on the price of the producer.	Stainless steel mesh oil filter with fittings. About the filtering capabilities compared to paper filters: ...results for the paper filters ranged from 48 microns for the best filter to over 300 microns for the worst filter. [...] Paper filters are rated on averages, percentages of efficiency (also known as beta ratios) and multiple passes, so a 10 micron rated paper filter (as advertised on the packaging) may be letting particles 50 microns and larger through. The medical grade stainless steel cloth that we use is consistent across the entire media surface and is rated at 35 microns, meaning nothing larger than 35 microns should pass through the material...	200 €
	Steering head bearing with tapered roller bearings - lower part (or both)	75 € (140 €)
	Cylinder boring and honing	60 €   2 for 100 €
	Lupo pistons: valve pockets "The whole deal": valve pockets, lightening, compression grooves - ca. 20 g. lighter Piston are ca. 50-70 € / piece - depending on make and retailer (2020). End result: ca. 400 cc	40 € 65 € /a piece
	Lightening of the Kokusan-rotor and with the "Hartmut-modification" More info about the advantages on my YouTube-Channel	60 €
	Lightening of the primary gear - ca. 450 g. lighter	75 €
	Leigth weight pushrods - ca. 10 g. lighter/a piece	25 € 4 for 80 €
	Clutch screws (set) 7075 alu. with slotted heads... or hex heads - ca. 22 g. lighter/set	35 € 40 €
	Lightening of the cogwheel - ca. 90 g. lighter Lightening of the flywheel - ca. 175 g. lighter	60 € 70 €
	Lightening of the outer clutch drum - ca. 70 g. lighter	60 €
	Valve guides - also custom measurements Replacement of valve guides, valve grinding and valve seat cutting (including valve guides) - per head: - 2 heads:	30 € /piece 100 € 180 €
	Cylinder heads thread repair - with brass insert	120 €
	Delivery Pick up and drop off of your Morini "My kilometers" - to and fro	0,40€ /km
Cleaning	If I get dirty parts, engines or bikes I take special payment for cleaning. It's a "crappy job", often hazardous and actually waste of a mechanics time and could as well have been done before delivery. Besides that cleaning agents is also an expense. For instance: an engine covered in chain grease, oil and dirt will cost you:	70 €
Custom jobs		Ask for price